Waryway · Guides · Purse Design print and cut

Print and cut a Purse Design pattern

Print a Purse Design pattern at 1:1, measure the calibration squares, tape the overlap ticks, punch through the paper into the leather, then cut. Always download the PDF from the editor — HTML print is a backup. Every millimetre number is dual mm (in) — for example 250 mm (9.84 in). Wallet sleeves, lining + inside Off / Open slip / Zip-seal, zip-top (off by default; 3D closed when on), slouch cut ease, and the 1:1 ruler grid are on the same pattern.

Purse Design Print 1:1 Leather Dual mm (in) Lining Wallet Zip Grid Letter / A4

Print at actual size (1:1)

A Purse Design PDF is a full-scale leather pattern. If the driver scales it, punch holes and seam allowances land in the wrong place. The editor overlay repeats this ritual every time you download:

Actual size / 100%. Do not Fit to page. Turn off headers/footers.

Borderless only if the printer truly has it — see safe margins.

  1. Open Purse Design and unfold the style you want.
  2. Download PDF Letter or A4 from the editor (confirm the print ritual first).
  3. In the print dialog: Actual size / 100%. Do not Fit to page. Turn off headers/footers.
  4. Print one sheet, then measure before you print the rest of a multi-page tile.

Browser “Print this page” on this guide is a how-to backup. The pattern geometry lives in the PDF.

Measure the 50 mm (1.97 in) and 2 in squares

Every Purse Design PDF carries two calibration squares. After the first sheet comes out, put a ruler on both of them before you cut leather:

SquareMust readIf it does not
Metric 50 mm (1.97 in) on each side Reprint at 100% / Actual size
Imperial 2 in on each side Reprint at 100% / Actual size

Measure both. A driver that “almost” scaled can still pass a glance at one square. If either the 50 mm (1.97 in) square or the 2 in square is wrong, reprint at 100% / Actual size. Do not stretch the paper or the leather to match.

Tape ticks, punch, then cut

Multi-page tiles overlap. The PDF draws overlap ticks so sheets register without guessing. Assembly order:

  1. Tape the overlap ticks. Align tick to tick, then tape the sheets into one pattern. Do not trim the overlap until the whole panel is registered.
  2. Lay the paper on the leather (grain and hide flaws already chosen). Tape or weight so it cannot creep.
  3. Punch through the paper into the leather. Stitch / punch marks transfer only if the awl or punch goes through both layers.
  4. Then cut. Cut the leather after punches exist. Cutting first loses the registration that the ticks and holes were for.

Ritual in one line. Actual size, measure the square, tape the ticks, punch through the paper into the leather, then cut.

Safe margins vs borderless

Purse Design defaults to Safe margins (recommended). The PDF keeps pattern ink ≥ 8 mm (0.31 in) from the sheet edge. You can opt into borderless in the editor if your printer actually supports it.

ModeWhen
Safe margins (recommended) Default. PDF keeps ink ≥ 8 mm (0.31 in) from the edge.
My printer can do borderless Only if the driver really prints to the edge. A PDF cannot force that.

Honesty: a PDF cannot force the driver; many inkjets keep ~5 mm (0.20 in) unprintable. If you pick borderless and the driver still clips, reprint with Safe margins.

Shaped leather: radius, slouch, arc gusset

Corner radius plus slouch ease 0–80 mm (0.00–3.15 in) is cut ease on body height — extra millimetres added to the unfold so the leather can slump. It is not a cloth sim and not a mesh unwrap.

When radius is greater than 0, the gusset finished length is side + bottomArc + side, not 2H+W. Curved edges use arc length, never bounding-box width or chord width.

The 3D sag view is preview only. Unfold is the measurement you print and cut.

Cut from the unfold. Arc-length gussets and slouch cut ease live on the 2D pattern. Do not scale pieces from the 3D preview.

Wallet sleeves

Style Wallet is a bifold wrap with a center FOLD. The closed size defaults to 80×110 mm (3.15×4.33 in). The pattern stacks 3 card sleeves, a thumb notch, and an optional lining liner.

Attachments are extra pieces on the same PDF. No v3 inside-zip on wallet. Wallet liner stays as today — no v3 lining-panel requirement.

Lining and inside pockets

A lining checkbox is on tote and pouch (wallet liner as today).

Inside pocket UI: Off / Open slip / Zip-seal. Default Off. Host is lining-back. Width / height default 120×140 mm (4.72×5.51 in) when not Off.

ModePattern
Off No inside pocket pieces.
Open slip Extra piece, stitch three sides, top hem, no zipper-facing.
Zip-seal Pocket + facing(s); teeth ≈ pocket width; notches IP1.

Exterior Patch still works with lining on (different host): extra CUT, three-side stitch, top hem.

Wallet: no v3 inside-zip / lining-panel requirement (sleeves as today).

Zip-top (3D closed when on)

A zip-top toggle is on tote and pouch, off by default.

Pattern still adds two facing strips. Length equals the opening (arc or width). Notches are Z1 (front facing) and Z2 (back facing). Teeth print as a dashed centerline — not a coil mesh. Opening arc is unchanged.

3D when zipper on: front and back rims meet (no open U). The zipper coil sits on that closed seam; the pull is visible. Slouch may still belly, but the opening is zipped shut. Exploded view: facings peel off the closed seam. Straps stay at the high corners, not through the zip.

3D when zipper off: open tote/pouch as today (dipped rim if slouch). 3D is a conceptual preview; unfold is the source of truth.

1:1 millimetre ruler grid

Purse Design draws a 1:1 millimetre ruler grid so you can check scale on screen, in 3D, and on the PDF cover. Labels use dual mm (in):

SurfaceGrid
2D SVG 10 mm (0.39 in) minor / 50 mm (1.97 in) major
3D floor 50 mm (1.97 in) squares plus a vertical 100 mm (3.94 in) billboard
PDF cover 10 mm (0.39 in) / 50 mm (1.97 in) behind the 50 mm (1.97 in) and 2 in calibration squares
Tile pages Stay clean unless you opt the grid in

The editor checkbox defaults on. Tile pages stay clean unless opted in — the grid must not hide punch marks or overlap ticks on the cut sheets.

v1 JSON still unfolds

v1 JSON without new fields still unfolds to the old rectangles. Missing v2 fields = v1: no corner radius, no slouch cut ease, no wallet sleeves, zip-top off, pockets off, box gusset 2H+W.

Missing v3 fields = current v2 behaviour: no lining panels, inside pocket Off, zip-top 3D open (rims do not meet).

3D sag remains preview only even when slouch ease is set. Unfold is the measurement.

Always download the PDF

The 1:1 tiled pattern is a PDF from https://waryway.com/purse-design/. Use Download PDF Letter or Download PDF A4 in the editor (the print ritual modal confirms first).

HTML @page on this how-to is a secondary print of the instructions only. Do not treat a browser print of this page as the leather pattern.

Try it

Open Purse Design, unfold a style, download PDF Letter, print one sheet at Actual size / 100%, measure the 50 mm (1.97 in) square and the 2 in square, then tape the overlap ticks.